...
 | Installation manual IPR-IX10-xxx
|
...
T-568B, or another cable which meets the requirements as specified in Maximum cable lengths.
This document assumes standard T-568-B color coding of the cables.Wire side cutter
Electric wire ferrule
Crimping tool
Philips screwdriver
...
The Sirius iX10 card reader is suitable for indoor use in an enclosure.
For proper operation, the reader must be installed behind a panel of 9mm (plexi) glass.
The IP rating of the Sirius iX10 card reader depends on the enclosure in which the iX reader is placed.
The Sirius iX10 operates between a temperature of -40°C and + 85°C.
Determine the location where the Sirius iX10 card reader should be installed. Please note that there is a maximum cable length between the card reader and the door controller (Maximum cable lengths).
The connection and cable length of the Sirius iX10 depends on the chosen data output.The Sirius iX10 should not be installed directly on metal.
The reader is intended as a built-in module. Put the reader as close to the front plate as possible, everything placed in front of the reader decreases the RFID (radio frequency identification) range.
The Sirius iX10 should not be mounted higher than two meters.
Keep a minimum distance of 20 cm between Sirius iX10 card readers *1.
...
The configuration defines which card type is read by default by the Sirius iX10.
Functionality | IPR-iX10-MDF | IPR-iX10-UID | IPR-iX10-PRM | IPR-IX10-USB |
|---|---|---|---|---|
Communication | RS485 | RS485 | RS485 | RS485 |
Cosmos Access support | yes | yes | yes | yes |
Card data output | Clock/data | Clock/data | - | USB (HID) |
Output length | 8 or 12 digits | 10 or 17 digits | - | ASCII |
Read coded TKH cards | Yes | No | - | - |
Read CSN | No | Yes | - | - |
Reads Configuration cards | No | No | Yes | Yes |
Tamper output | Yes | Yes | - | - |
Buzzer input | Yes | Yes | - | - |
LED input | Yes | Yes | - | - |
Default LED color | Red/Green | Red/Green | Blue | Blue |
5.2.1 IPR-iX10-MDF
The Sirius iX10 IPR-iX10-MDF can read both TKH coded MIFARE Classic cards and TKH coded MIFARE DESFire cards simultaneously. The table below shows an example of the reader output format.
...
Interface / protocol | How to program |
RS485 | Reader configuration file (iProtect) |
Wiegand, Clock/data | TKH Security configuration card |
...
, see below |
TKH Security configuration card
If the reader is not used with RS485, a configuration card can be is used to program the reader to the customer needs. Settings like the default LED color and brightness, Wiegand or Clock/data output and key material can be changed. To program the programmable reader, a customer specific (config) card is needed.
This configuration card can be ordered at TKH Security via cardconfig@tkhsecurity.com.
Programming procedure
Connect the card reader.
Switch on the power. The card readers LED turns into BLUE.
Present the configuration card and wait until the card reader restarts.
The card readers LED turns into RED. The configuration is complete.
5.1.3 IPR-iX10-USB HID reader
The Sirius iX10 IPR-iX10-USB does not have any configuration by default. If the reader is connected to RS485, the reader is automaticly configured. Else, use a TKH Security configuration card to set configure the reader to the correct (USB) mode.
Configuration card
If the reader is not used with RS485, a configuration card can be used to program the reader to the customer needs. Settings like the default LED color and brightness, USB keyboard layout and key material can be changed. To program the USB reader, a customer specific (config) card is needed.
This configuration card can be ordered at TKH Security via cardconfig@tkhsecurity.com.
6. Sticker
The Sirius iX10 is provided with the stickers as shown in the table below:
...