...
 | Installation manual IPR-IX10
|
This document contains the information needed for installing the Sirius iX10. Details and recommendations are described in the chapters below. This manual represents the knowledge at the above-mentioned date. TKH security works non-stop to improve the products. For the most recent technical information please contact your consultant or dealer.
1. Table of content
| Table of Contents | ||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
2. General
The Sirius iX10 is the smallest card reader of the iX family. The reader is compatible with a variety of cards and tags. This reader is perfect for built-in situations, like electrical junction boxes and wall boxes.
You can use the iX10 reader in places where other iX family readers are just too big. The reader is supplied with a basic casing that prevents the electronics from being damaged during installation.
2.1. Features
RfID (radio frequency identification) reader for MIFARE/DESFire cards
IPROTECT Access compatible (BLE) (Mobile access)
Ultra-fast response time
RGB power LED
Multi-tone buzzer
Movement detection tamper
Removable connector
3. Installation preparations
3.1 Tools and equipment
When installing the Sirius iX10, the following tools or materials may be needed.
T-568B, or another cable which meets the requirements as specified in Maximum cable lengths.
This document assumes standard T-568-B color coding of the cables.Wire side cutter
Electric wire ferrule
Crimping tool
Philips screwdriver
3.2 Accessory
3.2.1 Adapter board
An adapter board can be placed between the controller and the Sirius card reader to convert signals or for electrical protection. Reasons for the use of an adapter board include:
If the reader is not installed in the same building as the controller and therefore, the cable exits the building. This scenario may occur if, for example, the reader is installed near a parking barrier.
If The connection cable is not (or is not guaranteed to be) a (≥Cat5e) UTP cable (e.g., if an
existing connection cable is being reused)Overvoltage protection is required
The adapter board along with the network controller are connected using standard UTP ≥Cat5e
cable (plug-in connection).
3.2.2.1 Connecting a Clock/data or RS485 reader
...
| Info |
|---|
For more information, please refer to the adapter board manual. |
3.2.2 Mounting plate
If you need a mounting- or adapter plate, please contact TKH Security for a suitable solution.
4. Installation
This chapter describes the conditions to install the iX10 reader.
4.1 Measurements
4.2 Environment
To ensure proper functioning of the equipment, the environment of the Sirius iX10 must be compliant with certain conditions.
The Sirius iX10 card reader is suitable for indoor use in an enclosure.
For proper operation, the reader must be installed behind a panel of 9mm (plexi) glass.
The IP rating of the Sirius iX10 card reader depends on the enclosure in which the iX reader is placed.
The Sirius iX10 operates between a temperature of -40°C and + 85°C.
Determine the location where the Sirius iX10 card reader should be installed. Please note that there is a maximum cable length between the card reader and the door controller (Maximum cable lengths).
The connection and cable length of the Sirius iX10 depends on the chosen data output.The Sirius iX10 should not be installed directly on metal.
The reader is intended as a built-in module. Put the reader as close to the front plate as possible, everything placed in front of the reader decreases the RFID (radio frequency identification) range.
The Sirius iX10 should not be mounted higher than two meters.
Keep a minimum distance of 20 cm between Sirius iX10 card readers *1.
| Info |
|---|
*1 When Cosmos Access is used, keep a minimum distance of 40 cm between Sirius iX10 readers. |
| Note |
|---|
Metal near the Bluetooth and/or rfID antenna, such as cables or metal screws, can negatively affect the user experience for Cosmos access or card reading. |
4.3 Mounting steps
Open the housing (enclosure) where iX10 is going to be installed. Do not open the protective case of iX10.
Remove the 9-pin connector from the iX10.
Connect the cable correctly to the 9-pin connector. See chapter 8.1 Main connector.
Put back the connector.
Mount the card reader on a flat surface.
Close the housing (enclosure) in which the module is installed.
4.4 Advanced options
The iX10 is intended to be used in electrical wall sockets, but it is possible to make the iX10 fit in other housings. Therefore, it is equipped with breakaway tabs, numbered 1 … 4.
|  |
5. Compatibility & configurations
5.1 Compatibility
The iX10 reader is compatible with the following devices.
...
| Note |
|---|
The iX10 reader is not supported by firmware versions below 2.9.x. With iProtect 10.3 and below, the auto provisioning should be disabled for iX10 readers. |
5.2 Configurations
The configuration defines which card type is read by default by the Sirius iX10.
Functionality | IPR-iX10-MDF | IPR-iX10-UID | IPR-iX10-PRM |
|---|---|---|---|
Communication | RS485 | RS485 | RS485 |
Cosmos Access support | yes | yes | yes |
Card data output | Clock/data | Clock/data | - |
Output length | 8 or 12 digits | 10 or 17 digits | - |
Read coded TKH cards | Yes | No | - |
Read CSN | No | Yes | - |
Reads Configuration cards | No | No | Yes |
Tamper output | Yes | Yes | - |
Buzzer input | Yes | Yes | - |
LED input | Yes | Yes | - |
Default LED color | Red/Green | Red/Green | Blue |
5.2.1 IPR-iX10-MDF
The Sirius iX10 IPR-iX10-MDF can read both TKH coded MIFARE Classic cards and TKH coded MIFARE DESFire cards simultaneously. The table below shows an example of the reader output format.
Example | MIFARE Classic output | MIFARE DESFire output |
|---|---|---|
System code | 4 digits: 1234 | 6 digits: 123456 |
Card number | 4 digits: 6789 | 6 digits: 789012 |
Result | 12346789 | 123456789012 |
5.1.2 IPR-iX10-UID
The Sirius iX10 reads both 4-byte and 7-byte CSN simultaneously. The table below shows an example of the reader output format.
Example | 4Byte UID output | 7Byte UID output |
|---|---|---|
UID | 10 digits | 17 digits |
Result | 123467890 | 123456789012 |
5.1.3 IPR-iX10-PRM Programmable
The Sirius iX10 IPR-iX10-PRM does not have any configuration by default. Programming the Sirius iX10 depends on the interface.
Interface / protocol | How to program |
RS485 | Reader configuration file |
Clock/data | TKH Security configuration card |
Configuration card
If the reader is not used with RS485, a configuration card can be used to program the reader to the customer needs. Settings like the default LED color and brightness, Wiegand or Clock/data output and key material can be changed. To program the programmable reader, a customer specific (config) card is needed.
This configuration card can be ordered at TKH Security via cardconfig@tkhsecurity.com.
Programming procedure
Connect the card reader.
Switch on the power. The card readers LED turns into BLUE.
Present the configuration card and wait until the card reader restarts.
The card readers LED turns into RED. The configuration is complete.
6. Sticker
The Sirius iX10 is provided with the stickers as shown in the table below:
...
The product is classed as Electrical or Electronic equipment and should not be disposed with other household or commercial waste at the end of its useful life. The Waste of Electrical and Electronic Equipment (WEEE) Directive has been put in place to recycle products using best available recovery and recycling techniques to minimize the impact on the environment, treat and hazardous substances and avoid the increasing landfill. Contact local authorities for information on the correct disposal of Electrical or Electronic equipment.
7. Mobile Access
Mobile access is an extra feature on the Sirius iX10. Using the IPROTECT Access app (formerly Cosmos Access), the user can use a mobile device as an identifier (besides rfID access cards). To enable this feature, every Sirius iX10 must be assigned to the Mobile Access project it belongs to. This can be done using the assign process.
...
For more detailed information please check the IPROTECT Config and IRPOTECT Access documentation.
8. Interfaces
The following interfaces are by default available on the Sirius iX10:
...
Label | Interface | Description |
|---|---|---|
A | Power LED | Multicolor RGB LED to display status |
B | BLE antenna | Antenna location for Cosmos Access |
C | Buzzer | Multi-tone buzzer to provide user feedback |
D | 9 Pin connector | Connector to connect card reader to door controller |
E | USB (Universal Serial Bus) | Micro USB connection (optional), to support HID (Human Interface Devices) |
- | Tamper | Tamper with movement sensor (accelerometer) |
8.1 Main connector
...
Pin | Description | |
|---|---|---|
| 1 | V+ | 5 … 28VDC power connection* |
| 2 | GND | Ground |
| 3 | A | RS485 A |
| 4 | B | RS485 B |
| 5 | LED | Activate LED input |
| 6 | BUZ | Activate Buzzer input |
| 7 | TAMP | Tamper contact |
| 8 | D0 | Clock/data or Wiegand, open drain |
| 9 | D1 | Clock/data or Wiegand, open drain |
| Info |
|---|
* The Sirius iX10 accepts a power between 5 .. 28 VDC. A higher input voltage results in lower power consumption and ensuring cost-efficient wiring with a smaller conductor diameter. When using an external power supply, it must comply with SELV guidelines. It is recommended to power the reader with a power supply that can supply a minimum of 3W to a maximum of 15W. If the reader is powered by a power supply with a power higher than 15W, a fuse of 400mA must be placed by the installer. |
8.2 Connecting the reader via RS485
Recommended cable type between an Orion and the Sirius iX10 card reader is:
...
Pin | Cable color | Signal | T568B Pair | ||
| 1 | White/orange |  | B | B |
2 | Orange |  | A | A | |
3 | White/green |  | B | B | |
4 | Blue |  | VCC | 5..28 VDC | |
5 | White/blue |  | - | - | |
6 | Green |  | A | A | |
7 | White/brown |  | - | - | |
8 | Brown |  | GND | GND | |
8.3 Clock/data or Wiegand
Recommended cable type between the Orion or Orbit and Sirius iX10 card reader:
...
Cable color | Door controller | Sirius iX10 | |
|---|---|---|---|
Green |  | Data/D0 | D0 |
Yellow |  | Clock/D1 | D1 |
Pink |  | VCC (+) | 5-28VDC |
Grey |  | LED | LED |
White |  | GND | GND |
Brown |  | GND | GND |
8.3.1 Signals
The table below shows the typical timing of the communication signals.
Signal | Frequency (max) | High | Low |
|---|---|---|---|
Wiegand | 1 kHz | ≥ 500 μs | ≥ 500 μs |
Clock / Data | 666 Hz | ≥ 1ms | ≥ 500 μs |
8.4 Maximum cable lengths
In most cases, the maximum cable length depends on the length of the communication interface.
...
| Info |
|---|
*1 The cable type and length are dictated by the desired length for the communication *2 Twisted pair, shielded cable must be used; UTP CAT5e or CAT6, AWG 24. Please be sure that the cable used for RS485 suits the RS485 protocol. *3 Non shielded cables, smallest conductor size with 12VDC supply. |
8.5 USB
Maximum cable length as USB 2.0 specification (3 meter).
9. Technical specifications
Power | |||
supply voltage | 5 … 28VDC (max 2W) | ||
Housing and dimensions | |||
Color | Black | ||
Full size with breakout tabs | 68 x 68 x 22 mm (about 2.68 x 2.68 x 0.87 in) | ||
Protective cap size | 51 x 51 x 15 mm (about 2.01 x 2.01 x 0.59 in) | ||
PCB only size | 49 x 49 x 22 mm (about 1.931 x 1.93 x 0.87 in) | ||
Environment | |||
IP rating | N/A (depending on enclosure)
| ||
Operating temperature | -40 … 85oC | ||
Storage temperature | -40 … 85oC (industrial grade) | ||
Operating humid | 5 - 95% relative humidity, non-condensing | ||
Installation | |||
Location | The iX10 is intended for installation in a housing (enclosure). | ||
Minimum distance | 20 cm between iX10’s for rfID | ||
Interface | |||
Type | Auto select, only one interface at a time | ||
Wiegand | Simplex (read only), cable length up to 120 meters | ||
Clock/data | Simplex (read only), cable length up to 50 meters | ||
RS485 | Half duplex, cable length up to 600 meters (115k2) | ||
Compatibility | Compatible with TKH Orion, Orbit and ApolloN.
| ||
RfID cards | |||
Frequency | 13,56MHz | ||
Standard | ISO14443-A | ||
Type | MIFARE Classic cards, MIFARE DESFire 0.6, EV1, EV2 and EV3 cards
| ||
Maximum distance | MIFARE classic card: up to 65mm (about 2.56 in) MIFARE DESFire EV1 card: up to 25mm (about 0.98 in) MIFARE DESFire EV2 card: up to 50mm (about 1.97 in) MIFARE DESFire EV3 card: up to 50mm (about 1.97 in) MIFARE DESFire EV1 tag: up to 20 mm (about 0.79 in) MIFARE DESFire EV2 tag: up to 35mm (about 1.38 in) MIFARE DESFire EV3 tag: up to 35mm (about 1.38 in) | ||
Mobile Access | |||
Frequency | 2,4 GHz band | ||
Standard | Bluetooth Low Energy (BLE) | ||
Type | TKH Security Mobile Access | ||
Distance | 0…20 cm (default) | ||
Main header | |||
Type | 9 pin removable screw header | ||
Input: ‘Drive LED’ | With internal pull-up | ||
Output: ‘Tamper is active’ | Open drain without pull-up | ||
User interface | |||
Optic | RGB power LED | ||
Sound | Multi tone buzzer, 85dB at 1 m | ||
Additional features | |||
Tamper | Accelerometer sensor | ||
Certification | |||
Electric | EMC, LVD | ||
Radio | RED | ||
BLE | http://Bluetooth.com certified | ||
Variants / order code | |||
IPR-iX10-MDF | MIFARE DESFire coded | ||
IPR-iX10-UID | UID card | ||
IPR-iX10-PRM | Programmable | ||
...