...
Installation Manual | IM-20210309-TP-47 Access Control | Controllers | Apollo(N) Network Controllers |Polyx™ Controllers | |
|
| Table of Contents |
|---|
This manual represents the knowledge at the above-mentioned time. TKH security works non-stop to improve her products. For the most recent technical information please contact your consultant or dealer.
...
If the reader manager firmware is not up-to-date, please execute the following steps:
Open a web browser on your PC or laptop:
Enter the IP address of the Polyx (e.g. http://192.168.1.195).
The upload of the page appears:
2.2.2 If Pluto
The Pluto reader manager firmware will be automatically updated through provisioning.
2.3 Loading Applet
Download the compressed applet file from the knowledge bank of TKH Security.
Double click on the file you have downloaded. Subsequently it will be executed in the
directory, where the downloaded file is located. Place the files in a directory on your pc or
laptop.
...
3 Using the Applet
Double click on the KpController-externaluse.jar.
The following main page will appear:
...
Choose if the configuration concerns a Polyx device or Pluto device.
2. If Polyx, please go to chapter 4
3. If Pluto, please go to chapter 5
...
This chapter will describe how to configure the Polyx device.
Press on “Polyx device” in the main page
Press on “configure device”
The Polyx configuration window will appear:
...
4.1 Tab sheet independent functions
...
Open:
It is possible to open earlier created by this applet .taz files with the “open” button.
Press “open”.
Browse to the correct file and select it.
Press “open”.
Save the information into the configuration file:
With this checkbox it is possible to determine separately for each tab sheet, whether the data must be saved or not. By disabling this checkbox, the tab sheet will not be saved.
...
Save:
This function will save the tab sheets where “save the information into the configuration file” is enabled.
Press “save”
Specify a logical name
Press “save”
Navigate:
This menu will allow the user to within the Keyprocessor hardware control application. The following menus are available:
...
STX/ETX – A serial version of the ABA-CLK/DAT protocol. This protocol is only suitable for readers (SmartID) with one-way data communication from the reader.
Here, the Polyx should be provided with a card protocol.SmartID t=cl – The reader is fully managed by the Polyx. Here, the Polyx should be provided with a card protocol and keystore.
Sirius (801-5050) – The reader is fully managed by the Polyx. Here, the Polyx should be provided with a card protocol and keystore.
Sirius i-series – The reader is fully managed by the Polyx. Here, the Polyx should be provided with a card protocol and keystore.
Vandal proof (801-501x) – The reader is fully managed by the Polyx. Here, the Polyx should be provided with a card protocol and keystore.
Sirius LEGIC – Protocol to handle Sirius LEGIC readers.
Aperio – Protocol for Aperio fittings. Here the Polyx should be provided with a card protocol.
Sallis – Protocol for Sallis fittings. Here the Polyx should be provided with a card protocol
OSDP – open standard protocol.
PHG Legic – Protocol for PHG Legic card readers. Here, the Polyx should be provided with a card protocol.
PHG Rs485 – Protocol for PHG finger scan reader. Here, the Polyx should be provided with a card protocol.
Press on the dropdown menu from the “protocol”
Select the desired reader protocol
Baudrate:
Depending on the selected type of reader, the default baud rate will be loaded (do not change this setting!).
Card protocol:
Here the available card protocols are visible. The protocols available depends on the reader protocol.
Press on the dropdown menu from the “card protocol”
Select the desired protocol.
Active LED:
Here the default LED color can be defined. The active LED color is the default LED color of the card reader.
...
This chapter will describe how to configure the Pluto device.
Press on “Pluto device” in the main page
Press on “configure device”
The Pluto configuration window will appear:
...
Open:
It is possible to open earlier created by this applet .taz files with the “open” button.
Press “open”.
Browse to the correct file and select it.
Press “open”.
Save the information into the configuration file:
With this checkbox it is possible to determine separately for each tab sheet, whether the data
must be saved. By disabling this checkbox, the tab sheet will not be saved.
...
Save:
This function will save the tab sheets where “save the information into the configuration file” is enabled
Press “save”.
Specify a logical name.
Press “save”.
Navigate:
This menu will allow the user to within the Keyprocessor hardware control application. The
following menus are available:
...
STX/ETX – A serial version of the ABA-CLK/DAT protocol. This protocol is only suitable for readers with one-way data communication from the reader. Here, the Polyx should be provided with a card protocol.
Sirius (801-5050) – The reader is fully managed by the Polyx. Here, the Polyx should be provided with a card protocol and keystore.
Sirius i-series – The reader is fully managed by the Polyx. Here, the Polyx should be provided with a card protocol and keystore.
Sirius LEGIC – Protocol to handle Sirius LEGIC readers.
Wiegand converter – Protocol to handle Wiegand converters.
Sallis – Protocol for Sallis fittings. Here the Polyx should be provided with a card protocol
PHG – Protocol for PHG finger scan reader. Here, the Polyx should be provided with a card protocol.
OSDP – open standard protocol.
Press on the dropdown menu from the “protocol”
Select the desired reader protocol
Baudrate:
Depending on the selected type of reader, the default baud rate will be loaded (do not change it!).
Card protocol:
Here the available card protocols are visible. The protocols available depends on the reader protocol.
Press on the dropdown menu from the “card protocol”
Select the desired protocol
Active LED
Here the default LED color can be defined. The active LED color is the default LED color of the card reader.
...