IPC-SP54 - Motorized with D0/D1 card reader
- MB
Installation Manual | IM-iProtect-IPC-SP54-221228 Access Control | IPC-SP54 - Motorized with D0/D1 card reader | 
|
Table of contents
This manual represents the knowledge at the above-mentioned time. TKH security works non-stop to improve her products. For the most recent technical information please contact your consultant or dealer.
1. Introduction
This document describes how to connect the IPC-SP54 (motorized card reader) to an Orion door controller and how to program it in iProtect.
This IPC-SP54 (Motorized card reader) is supported with: Sirius reader (D0/D1)
2. Motorized card reader unit
2.1 Power connector: Motorized card reader unit
PIN | Wire color | Name | Description |
1 | Orange | Power (+) | 24V DC |
2 | Black | GND (-) | Ground |
2.2 Green screw connector: 4 poles
PIN | Wire color | Name | Description | Orion door controller |
1 | Purple | Output | Return card | O2/O5 |
2 | Grey | Output | Collect card | O3/O6 |
3 | Yellow | Input | Card detection front | A2/A5 |
4 | Black | GND | Ground | C |
2.3 Green screw connector: 5 poles
PIN | Wire color | Name | Description | Orion door controller |
1 | Blue | Reader power | 5-12V DC | V+ |
2 | Brown | Reader ground | GND | C |
3 | White | Output | Activate Unit | O1/O4 |
4 | Orange | Reader - D0 | Data | D0 |
5 | Green | Reader - D1 | Clock | D1 |
3. iProtect reader settings
This chapter describes how to create the motorized card reader with and without vehicle detection.
3.1 Add reader
In iProtect, browse to menu: Installation | Hardware | Node
Enter the controller name to which the motorized card reader should be connected or add a new Orion door controller.
Right click on the "Orion Node" that was just selected or created and choose "Add reader".
Enter a logic “Name“, select a “Sub number“ (reader 1 or reader 2).
In tab General, select the “Card data interpretation“ and press save.
In tab Door behavior, create an area change “from area” X to area “outside for access control”.
3.1.1 With vehicle detection
In the Input/Output tab of the reader, select “Motorized card reader” under I/O type and make the following settings:
Input | Input number | Type |
Loop | A1/A4 - Monitored input | Normaly open |
Card precense | A2/A5 - Monitored input | Normaly closed |
Output | Output number | Logical status |
Return card | O3/O6 - Digital output | Not inverted (Yes) |
Collect card | O2/O5 - Digital output | Not inverted (Yes) |
Door control | H1/H2 - High power output | Not inverted (Yes) |
Right click on the "Orion Node" that was just selected or created and choose "Add output".
Output | Output number | Source | Input | Logical status |
Activate unit | O1/O4 - Digital output | Input status | Loop (A1/A4 - Monitored input) | Not inverted (Yes) |
3.1.2 Without vehicle detection
In the Input/Output tab of the reader, select “Motorized card reader” under I/O type and make the following settings:
Input | Input number | Type |
Loop | A1/A4 - Monitored input | Normaly closed |
Card precense | A2/A5 - Monitored input | Normaly closed |
Output | Output number | Logical status |
Return card | O3/O6 - Digital output | Not inverted (Yes) |
Collect card | O2/O5 - Digital output | Not inverted (Yes) |
Door control | H1/H2 - High power output | Not inverted (Yes) |
3.1.3 Reader | Other
To determine how you handle the visitor cards, at "Visitors” and “Log out visitor" you can choose from:
Always de-register visitor
De-register visitor at last day
De-register visitor at last two days
Don’t de-register visitor
Only when using “Don’t de-register visitor” the card will never be taken.
3.2 Access card
In iProtect, browse to menu: Access | Card
Enter the person's name and press search.
Select this person's card where the motorized card reader should take the card in one of the following conditions:
Keep card (Always
Keep card on last day
Keepcard on last two days
4. Installation and collection tray
Description | Distance |
|---|---|
Maximum front plate thickness | 6mm |
The minimum free space on the inside of the housing | |
Right and left of the front | 20mm |
Bottom front plate | 100mm |
Top of front plate | 50mm |
Minimum installation depth collecting tray | 200mm |
4.1 Dimensions mounting front plate
5. Technical information IPC-SP54
Overall | IPC-SP54 (excluding collection tray) |
|---|---|
Outline dimensions | 120(H) x 126(L) x 124,5(W) mm |
Weight | 1 Kg (Approximately) |
Electronics | Specific PCB |
Ticket motion | Stepping motor |
Transport method | Rolls |
Ticket sensors | Photo sensors |
Power requirements | +24V DC +/-10% 3A |
Dimensions | |
Length | 85.60 mm |
Width | 53.98 mm |
Thickness | From 0.15 to 1.00 mm |
Environment | |
Operating temperature | From 0 to + 50°C |
Storage temperature | -20 to + 60°C |