...
| Tip |
|---|
PUBLIC |
Installation Manual | TM-20230511 iProtect Access / Security | Functionalities |Voxio-A-3100-A readerNEDAP NVITE  |
This manual represents the knowledge at the above-mentioned time. TKH security works non-stop to improve her products. For the most recent technical information please contact your consultant or dealer.
| Table of Contents |
|---|
1. Introduction
This article explains how you can implement the VOXIO-A-3100-A NEDAP NVITE reader based on OSDP communication and describes the functions and settings.
...
2. Support and license
Below is an overview of support for both the hardware and the software, including the necessary license:
Version | License |
|---|---|
Version 10.3.15 | iProtect basic license |
Sufficient reader license |
2.1 Supported cards
Card type | Description |
|---|---|
Desfire cards | TKH coded AES crypted |
QR code | iProtect Crypted QR |
Other cards or custom keys on request
3. What is OSDP
Open Supervised Device Protocol (OSDP) is an access control communications standard developed by the Security Industry Association (SIA) to improve interoperability among access control and security products.
...
| Info |
|---|
OSDP readers are only supported by stacked Orions (RS485 connection) |
4. Installation
4.1 Connecting the reader
PHG connector | SignalNedap cable pigtail | CAT5 cable > Orion PRT 1 or 2 | Pin 1 | Not in use | Pin 2 | Not in use | Pin 3 | B | Signal |
|---|---|---|---|---|---|---|---|---|---|
Green | White/Orange & White/Green | ||||||||
Pin 4Brown | A | Orange&Green | Pin 5 | Not in use | |||||
pin 6 | GNDBlack | Brown | |||||||
Pin 7 | VCC 8-30V DC | Blue | |||||||
Red | External Power supply |
| Info |
|---|
Max. cable distance between Orion and the PHG NVITE reader = 30 120 Mtr. This is based on CAT5E - 24AWG |
| Info |
This cable distance is based without installing cable. |
Reader must be powered by an external power supply
...
5. Implementation
5.1 General
OSDP readers are completely handled by the nodemanager, so the nodemanager should run to obtain access by a OSDP card reader.
The readermanager is not involved by handling the OSDP protocol
5.2.1 Configure the reader in iProtect
Follow the steps below to configure an OSDP reader:
...
The discover function for OSDP devices checks for the following settings:
Baudrate: 9600, 19K2, 115K2 baud, They are all non-parity, 8 bit, 1 stop bit
Device address: 0, 1, 2, 3, 4, 5, 6, 7, 8, 13, 14, 24
If other settings are necessary, set these settings manually.
5.2.2 NVITE OSDP defaults
OSDP address | 0 |
Communication speed | 9600 baud |
Port setting | N81 |
5.3 OSDP reader settings
For OSDP readers there are some specific settings.
...
| Info |
|---|
Most used setting for buzzer time = 2 |
5.4 Keypad buttons
...
Keypad
...
Description
...
1-9
...
Numeric numbers
...
C
...
On keypad is used as restore key to re-enter the PIN on the pending access request.
...
E
...
On keypad is used for reset pincode (do not use as pincode only key).
...
6. Secure channel
OSDP v2 with Secure Channel has AES-128 encryption to ensure that communication between the targeted devices is strict and secure.
...
| Note |
|---|
Once a key is set into the reader it cannot be cleared or rewritten by the system (not allowed in the OSDP protocol, security risk). If the key must be cleared (Reset) follow the procedure what is delivered by the reader manufacturer. |