...

Installation Manual | IM-

20220714

20231122-MB-01

Access Control | Readers | Sirius Card Readers |

view-file

name	IM-20220714-MB-01.pdf

Table of Contents

This manual represents the knowledge at the above-mentioned time. TKH security works non-stop to improve her products. For the most recent technical information please contact your consultant or dealer.

...

This document assumes standard T-568-B color coding of the cables.

Image Modified	Pin number RJ-45 Plug	TIA/EIA-568-B Cable color	Signal ID	T568B Pair
	1	White/orange	DA+	2
	2	Orange	DA-	2
	3	White/green	DB+	3
	4	Blue	DC+	1
	5	White/blue	DC-	1
	6	Green	DB+	3
	7	White/brown	DD+	4
	8	Brown	DD-	4

1.2 Tools and equipment

When installing the Sirius iX30, the following tools or materials may be needed.

...

The following accessories are available for the Sirius iX30-IK

Mounting components	Part number
Mounting screw stainless steel 4,8 x 38 mm	801-5410
Plug Fisher Duopower S6 x 40 mm	801-5411

2. Installation

To ensure proper functioning of the equipment, the environment of the Sirius iX30-IK must be compliant with certain conditions.

...

The configuration defines which card type is read by default by the Sirius iX30-IK.

Functionality	801-5301 TKH coded	801-5302 CSN	801-5303 Programmable
Standard communication	RS485 & Clock/Data	RS485 & Clock/Data	-
Read CSN	No	Yes	-
Read coded TKH cards	Yes	No	-
Output length	8 or 12 digits	10 or 17 digits	-
Reads programable cards	No	No	Yes
Tamper output	Yes	Yes	-
Buzzer input	Yes	Yes	-
LED input	Yes	Yes	-
Default LED settings	Red/Green	Red/Green	Blue

3.1.1 801-5401 TKH Coded

The Sirius iX30-IK TKH coded can both read TKH coded Mifare classic cards and TKH coded Mifare DESFire cards simultaneously and works by default at the following devices.

Protocol	Hardware device (door controller)
RS485	Orion (stacked)
RS485	Polyx
Clock/Data	Orion (KpBus)
Clock/Data	Orbit
Clock/Data	Third party devices*

*since clock/data is an standard, the Sirius iX30-IK should work by default on third party controllers which supports the clock/data communication protocol. We strongly recommend to test it on forehand.

...

The Sirius iX30-IK reads both 4 byte and 7 byte CSN simultaneously and works by default at the following devices:

Protocol	Hardware device (door controller)
RS485	Orion (stacked)
RS485	Polyx
Clock/Data	Orion (KpBus)
Clock/Data	Orbit*
Clock/Data	Third party devices**

* 7byte CSN cannot be processed by the Orbit!

...

The Sirius iX30-IK 801-5303 programmable does not contain any configuration by default. Programming the Sirius iX30-IK depends on the connection/protocol.

Protocol	Hardware device (door controller)	How to program
RS485	Orion (stacked)	Reader configuration file
RS485	Polyx	Reader configuration file
Clock/Data	Orion (KpBus)	Configuration card
Clock/Data	Orbit*	Configuration card
Clock/Data	Third party devices**	Configuration card

Reader configuration file:

...

The following interfaces are by default available on the Sirius iX30-IK.

...

Label	Interface	Description
A	Light guide	Multicolor RGB LED to display current status
B	Buzzer	Multitone buzzer for audio feedback
C	DIP switch	3-pins DIP switch for RS485 purpose
D	9-Pins connector	Connector to connect card reader to door controller
E	Tamper	Tamper to monitor sabotage

3.4 Connections

...

Pin	description
5-16VDC	Power connection (5-16 Vdc) *
GND	Ground
A	RS485 A
B	RS485 B
LED	Activate LED input
BUZ	Activate Buzzer input
TAMP	Tamper contact
D0	Clock/data- Wiegand, open collector
D1	Clock/data- Wiegand, open collector

* The Sirius iX30-IK accepts a power between 5.0 and 16.0 Vdc. A higher input voltage results in lower power consumption and ensuring cost-efficient wiring with a smaller conductor diameter. When using an external power supply, it must comply with SELV guidelines.

Advised to power the reader with a power supply that can supply a minimum of 5W to a maximum of 15W. If the reader is powered by a power supply with a power higher than 15W, a fuse of 500mA must be placed by the installer.

DIP SWITCH

Function	1	2	3	Image Modified DIP-switch 3: RS485 terminator
DEFAULT	Off	Off	On
Polyx	On	On	Off
Ext.	Off	Off	Off

3.4.1 RS485 directly

Recommended cable type between the Orion or Polyx and the Sirius iX30-IK card reader is:

...

If any of the above conditions applies, see chapter 4.4.2.

Image Modified	Pin number RJ-45 Plug	TIA/EIA-568-B Cable color	Signal	T568B Pair
	1	White/orange	B	B
	2	Orange	A	A
	3	White/green	B	B
	4	Blue	VCC	5-16VDC
	5	White/blue	-	-
	6	Green	A	A
	7	White/brown	-	-
	8	Brown	GND	GND

...

3.4.2 RS485 via Adapter board

...

Adapter board is connected with the door controller with a default UTP cat5 cable (or higher) (plug connection).

Or screw connection on adapter board	Or RJ45 connection on adapter board	TIA/EIA-568-B Cable color	Signal	Sirius iX30-IK
A (or1)	1	White/orange	B	B
B (or 2)	2	Orange	A	A
Y (or 3)	3	White/green	B	B
+	4	Blue	VCC	5-16VDC
	5	White/blue
Z (or6)	6	Green	A	A
	7	White/brown
-	8	Brown	GND	GND

Connect GND of the Adapter board to the local earth.
Connect the shield of the ground cable to the GND connection of the Adapter board.

...

CKY 3x2x0,14mm²
CKY 4x2x0,14mm²
CAT5 UTP four twisted pairs of 24AWG copper conductors
CAT6 UTP four twisted pairs of 24AWG copper conductors

TIA/EIA-568-B Cable color	Connection door controller	Sirius iX30-IK
White/orange	Data/D0	D0
Orange	TAMP	TAMP
White/green	Clock/D1	D1
Blue	VCC (+)	5-16VDC
White/blue	LED	LED
Green	BUZZ	BUZZ
White/brown	GND	GND
Brown	GND	GND

Cable color	Connection door controller	Sirius iX30-IK
Green	Data/D0	D0
Yellow	Clock/D1	D1
Pink	VCC (+)	5-16VDC
Grey	LED	LED
White	GND	GND
Brown	GND	GND

3.4.4 Cable lengths if connected directly to Orion

Cable	Communication protocol	Cable length(m)		Communication between
UTP ≥Cat5e	RS485 Powered from Orion	120	Orion and Sirius iX30-IK card reader
	RS485 External powered	600
	Wiegand	120
	Clock/Data	50

3.4.5 Cable lengths generic

Cable	Communication protocol	Cable length (m)	Communication between
	RS485*	600	Controller and Sirius iX30-IK card reader
	Wiegand	120
	Clock/Data	50

* Please be sure that the cable used for RS485, is suitable for the RS485 protocol.

...

4. Technical specifications


Power

supply

Supply voltage	5- 16VDC (max: 1,4W)
Measure

housing

Housing	145 x 82 x 24 mm
PCB	116 x 38 mm
Environment	IP rating

IP66

IP55

operating

Operating temp.

-35 … 60ºC

storage

Storage temp.

-40 … 85ºC

interface

Interface

header

Header

9-pins plug connector, small pitch (3.5 / 3.81 mm)

simplex

Simplex (read only)	Wiegand, open collector
Simplex (read only)	Clock data, open collector
RS485	Half duplex, support speeds up to 250Kbps ±2/4/8kV protection airgap discharge ±6 kV contact discharge, ±8 kV using the Human Body Model. Compatible with RS485 standard, Polyx, Orion and Apollo. (Configuration with DIP switches).
Frequencies	13,56MHz	Card detection
Frequencies	2,4GHz band	Wireless connection
Cards	Standard	ISO 14443-A

type

Type	Mifare Classic, Mifare DESFire 0.6, EV1 and EV2
Distance	20-70mm (normal operation)
Main header inputs	LED	With internal pull-up (switch to GND) (3.3V, <1mA, over voltage protected)
	Buzzer
Main header output	Tamper	Open collector without pull-up (max 500 mA, over voltage protected (Vcc))
	Clock/data- Wiegand
User interface	Optic	RGB led / Light guide

sound

Sound	Multi tone buzzer, 85dB at 1 meter
Certification	Electric	EMC / LVD / CE
Certification	Radio	R&TTE

Version	Old Version 5	New Version 6
Changes made by	Tom Polman	MB
Saved on	Sept 19, 2022	Nov 22, 2023

Versions Compared

Key

1.2 Tools and equipment

2. Installation

3.1.1 801-5401 TKH Coded

3.4 Connections

3.4.1 RS485 directly

3.4.2 RS485 via Adapter board

3.4.4 Cable lengths if connected directly to Orion

3.4.5 Cable lengths generic

4. Technical specifications

Page Comparison

Versions Compared

Key

1.2 Tools and equipment

2. Installation

3.1.1 801-5401 TKH Coded

3.4 Connections

3.4.1 RS485 directly

3.4.2 RS485 via Adapter board

3.4.4 Cable lengths if connected directly to Orion

3.4.5 Cable lengths generic

4. Technical specifications