...
Installation |
Product
Installation
Connection
Manual | IM-20231122-MB-01 Access Control | Readers | Sirius Card Readers | |
|
| Table of Contents |
|---|
This manual represents the knowledge at the above-mentioned time. TKH security works non-stop to improve her products. For the most recent technical information please contact your consultant or dealer.
Table of content
| Table of Contents | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|
|
1. General
...
1. General
The Sirius iX30 IK10 classified IP66 card reader is a versatile card reader which support multiple card technologies and communication protocols used in access control solutions. In addition, the Sirius iX30-IK is able to support different technologies simultaneously.
...
This document assumes standard T-568-B color coding of the cables.
| Pin number RJ-45 Plug | Cable color | Signal ID | T568B Pair |
1 | White/orange | DA+ | 2 | |
2 | Orange | DA- | 2 | |
3 | White/green | DB+ | 3 | |
4 | Blue | DC+ | 1 | |
5 | White/blue | DC- | 1 | |
6 | Green | DB+ | 3 | |
7 | White/brown | DD+ | 4 | |
8 | Brown | DD- | 4 |
1.2 Tools and equipment
When installing the Sirius iX30, the following tools or materials may be needed.
...
The following accessories are available for the Sirius iX30-IK
Mounting components | Part number |
Mounting screw stainless steel 4,8 x 38 mm | 801-5410 |
Plug Fisher Duopower S6 x 40 mm | 801-5411 |
2. Installation
To ensure proper functioning of the equipment, the environment of the Sirius iX30-IK must be compliant with certain conditions.
...
The configuration defines which card type is read by default by the Sirius IPR-iX30-IKiK10.
Standard communication
RS485 & Clock/Data
RS485 & Clock/Data
-
Read CSN
No
Yes
-
Read coded TKH cards
Yes
Functionality |
|---|
801-5301 TKH coded
801-5302 CSN
801-5303 Programmable
IPR-iX30-iK10-MDF | IPR-iX30-iK10-UID | IPR-iX30-iK10-PRM | |
|---|---|---|---|
Communication | RS485 | RS485 | RS485 |
Cosmos Access support | yes | yes | yes |
Card data output | Clock/data | Clock/data | - |
Output length | 8 or 12 digits | 10 or 17 digits | - |
Read coded TKH cards |
|---|
Yes | No |
Yes
- | |||
Read CSN | No | Yes | - |
|---|---|---|---|
Reads Configuration cards | No | No | Yes |
Tamper output | Yes | Yes | - |
Buzzer input | Yes | Yes | - |
LED input | Yes | Yes | - |
Default LED |
color | Red/Green | Red/Green | Blue |
|---|
3.1.1
...
IPR-iX30-iK10-MDF
The Sirius iX10 IPR-iX10-MDF can read both TKH coded MIFARE Classic cards and TKH coded Mifare MIFARE DESFire cards simultaneously and works by default at the following devices.
...
Protocol
...
Hardware device (door controller)
...
RS485
...
Orion (stacked)
...
RS485
...
Polyx
...
Clock/Data
...
Orion (KpBus)
...
Clock/Data
...
Orbit
...
Clock/Data
...
Third party devices*
*since clock/data is an standard, the Sirius iX30-IK should work by default on third party controllers which supports the clock/data communication protocol. We strongly recommend to test it on forehand.
3.1.1.1 Output differs per card type
TKH Security Mifare Classic:
4 digits system code e.g.: 1234
4 digits card number e.g.: 6789
Result as output: 12346789
TKH Security Mifare DESFire:
6 digits system code e.g.: 123456
6 digits card number e.g.: 789012
Result as output: 123456789012
3.1.2 801-5402 CSN
The Sirius iX30-IK reads both 4 byte and 7 byte CSN simultaneously and works by default at the following devices:
...
Protocol
...
Hardware device (door controller)
...
RS485
...
Orion (stacked)
...
RS485
...
Polyx
...
Clock/Data
...
Orion (KpBus)
...
Clock/Data
...
Orbit*
...
Clock/Data
...
Third party devices**
* 7byte CSN cannot be processed by the Orbit!
** since clock/data is an standard, the Sirius iX30-IK should work by default on third party controllers which supports the clock/data communication protocol. We strongly recommend to test it on forehand.
3.1.2.1 Output differs per card type
4Byte CSN:
10 digits CSN
Result as output: 1234567890
7Byte CSN:
17 digits CSN
Result as output: 12345678901234567
3.1.3 801-5403 Programmable
The Sirius iX30-IK 801-5303 programmable does not contain . The table below shows an example of the reader output format.
Example | MIFARE Classic output | MIFARE DESFire output |
|---|---|---|
System code | 4 digits: 1234 | 6 digits: 123456 |
Card number | 4 digits: 6789 | 6 digits: 789012 |
Result | 12346789 | 123456789012 |
3.1.2 IPR-iX30-iK10-UID
The Sirius IPR-iX30-iK10 reads both 4-byte and 7-byte CSN simultaneously. The table below shows an example of the reader output format.
Example | 4Byte UID output | 7Byte UID output |
|---|---|---|
UID | 10 digits | 17 digits |
Result | 123467890 | 123456789012 |
3.1.3 IPR-iX30-iK10-PRM
The Sirius iX10 IPR-iX30-iK10 does not have any configuration by default. Programming the Sirius IPR-iX30-IK iK10 depends on the connectioninterface.
Interface / protocol |
...
Protocol
...
Hardware device (door controller)
...
How to program
...
RS485
...
Orion (stacked)
...
Reader configuration file
...
RS485
...
Polyx
...
Reader configuration file
...
Clock/Data
...
Orion (KpBus)
...
Configuration card
...
Clock/Data
...
Orbit*
...
Configuration card
...
Clock/Data
...
Third party devices**
...
Configuration card
Reader configuration file:
A by the Hardware Controll Applet generated reader file which determines the exact configuration. This can be distributed central through iProtect.
Create reader configuration file.
Upload the file per line.
Detailed information can be found in the manual: TKH Security_HardwareControllApplet.
Configuration card:
...
How to program | |
RS485 | Reader configuration file |
Clock/data | TKH Security configuration card |
3.1.3.1 Configuration card
If the reader is not used with RS485, a configuration card can be used to program the reader to the customer needs. Settings like the default LED color and brightness, Wiegand or Clock/data output and key material can be changed. To program the programmable reader, a customer specific (config) card is needed.
This configuration card can be ordered at TKH Security via cardconfig@tkhsecurity.com.
3.1.3.2 Programming procedure
Connect the card reader.
Switch on the power. The card readers LED turns into BLUE.
Present the configuration card and wait until the card reader restarts.
The card readers LED turns into RED. The configuration is complete.
...
The following interfaces are by default available on the Sirius iX30-IK.
...
Label | Interface | Description |
A | Light guide | Multicolor RGB LED to display current status |
B | Buzzer | Multitone buzzer for audio feedback |
C | DIP switch | 3-pins DIP switch for RS485 purpose |
D | 9-Pins connector | Connector to connect card reader to door controller |
E | Tamper | Tamper to monitor sabotage |
3.4 Connections
...
Pin | description |
5-16VDC | Power connection (5-16 Vdc) * |
GND | Ground |
A | RS485 A |
B | RS485 B |
LED | Activate LED input |
BUZ | Activate Buzzer input |
TAMP | Tamper contact |
D0 | Clock/data- Wiegand, open collector |
D1 | Clock/data- Wiegand, open collector |
* The Sirius iX30-IK accepts a power between 5.0 and 16.0 Vdc. A higher input voltage results in lower power consumption and ensuring cost-efficient wiring with a smaller conductor diameter. When using an external power supply, it must comply with SELV guidelines.
Advised to power the reader with a power supply that can supply a minimum of 5W to a maximum of 15W. If the reader is powered by a power supply with a power higher than 15W, a fuse of 500mA must be placed by the installer.
DIP SWITCH
Function | 1 | 2 | 3 |  DIP-switch 3: |
DEFAULT | Off | Off | On | |
Polyx | On | On | Off | |
Ext. | Off | Off | Off |
3.4.1 RS485 directly
Recommended cable type between the Orion or Polyx and the Sirius iX30-IK card reader is:
...
If any of the above conditions applies, see chapter 4.4.2.
| Pin number RJ-45 Plug | Cable color | Signal | T568B Pair |
1 | White/orange | B | B | |
2 | Orange | A | A | |
3 | White/green | B | B | |
4 | Blue | VCC | 5-16VDC | |
5 | White/blue | - | - | |
6 | Green | A | A | |
7 | White/brown | - | - | |
8 | Brown | GND | GND |
...
3.4.2 RS485 via Adapter board
...
Adapter board is connected with the door controller with a default UTP cat5 cable (or higher) (plug connection).
Or screw connection on adapter board | Or RJ45 connection on adapter board | Cable color | Signal | Sirius iX30-IK |
A (or1) | 1 | White/orange | B | B |
B (or 2) | 2 | Orange | A | A |
Y (or 3) | 3 | White/green | B | B |
+ | 4 | Blue | VCC | 5-16VDC |
| 5 | White/blue |
|
|
Z (or6) | 6 | Green | A | A |
| 7 | White/brown |
|
|
- | 8 | Brown | GND | GND |
Connect GND of the Adapter board to the local earth.
Connect the shield of the ground cable to the GND connection of the Adapter board.
...
CKY 3x2x0,14mm²
CKY 4x2x0,14mm²
CAT5 UTP four twisted pairs of 24AWG copper conductors
CAT6 UTP four twisted pairs of 24AWG copper conductors
Cable color | Connection door controller | Sirius iX30-IK |
White/orange | Data/D0 | D0 |
Orange | TAMP | TAMP |
White/green | Clock/D1 | D1 |
Blue | VCC (+) | 5-16VDC |
White/blue | LED | LED |
Green | BUZZ | BUZZ |
White/brown | GND | GND |
Brown | GND | GND |
Cable color | Connection door controller | Sirius iX30-IK |
Green | Data/D0 | D0 |
Yellow | Clock/D1 | D1 |
Pink | VCC (+) | 5-16VDC |
Grey | LED | LED |
White | GND | GND |
Brown | GND | GND |
3.4.4 Cable lengths if connected directly to Orion
Cable | Communication protocol | Cable length(m) | Communication between | |
UTP ≥Cat5e | RS485 Powered from Orion | 120 |
Orion and Sirius iX30-IK card reader | |
RS485 External powered | 600 | |||
Wiegand | 120 | |||
Clock/Data | 50 | |||
3.4.5 Cable lengths generic
Cable | Communication protocol | Cable length (m) | Communication between |
| RS485* | 600 |
Controller and Sirius iX30-IK card reader |
Wiegand | 120 | ||
Clock/Data | 50 |
* Please be sure that the cable used for RS485, is suitable for the RS485 protocol.
Please take into account that the power supply at the reader must be between 5-16 VDC.
...
4.
...
Data signals
...
...
5. Technical specifications
...
Power |
Supply voltage | 5- 16VDC (max: 1,4W) |
Measure |
Housing | 145 x 82 x 24 mm | |
PCB | 116 x 38 mm | |
Environment | IP rating | IP66 |
Operating temp. | -35 … 60ºC |
Storage temp. | -40 … 85ºC |
Interface |
Header | 9-pins plug connector, small pitch (3.5 / 3.81 mm) |
Simplex | Wiegand, open collector | |
Clock data, open collector | ||
RS485 |
| |
Frequencies | 13,56MHz | Card detection |
2,4GHz band | Wireless connection | |
Cards | Standard | ISO 14443-A |
Type | Mifare Classic, Mifare DESFire 0.6, EV1, EV2 and |
EV3 | ||
Distance | 20-70mm (normal operation) | |
Main header inputs | LED | With internal pull-up (switch to GND) (3.3V, <1mA, over voltage protected) |
Buzzer | ||
Main header output | Tamper | Open collector without pull-up |
Clock/data- Wiegand | ||
User interface | Optic | RGB led / Light guide |
Sound | Multi tone buzzer, 85dB at 1 meter | |
Part number |
| |
Certification | Electric | EMC / LVD / CE |
Radio | R&TTE |