...
This manual represents the knowledge at the above-mentioned time. TKH security works non-stop to improve her products. For the most recent technical information please contact your consultant or dealer.
...
Below is an overview of support for both the hardware and the software, including the necessary license:
Version | License |
|---|---|
Version 10.3.15 | iProtect basic license |
Sufficient reader license |
2.1 Supported cards
TKH coded DESFire cards
QR code
...
4.1 Connecting the reader
Nedap cable pigtail | CAT5 cable > Orion PRT 1 or 2 | Signal |
|---|---|---|
Brown | Orange&Green | RS485 A |
Green | White/Orange & White/Green | RS485 B |
Black | Brown | 0VDC |
Red | External Power supply | 12-24VDC |
| Info |
|---|
Max. cable distance between Orion and the NVITE reader = 120 Mtr. This is based on CAT5E - 24AWG cable. |
...
5.2.2 NVITE OSDP defaults
OSDP address | 0 |
Communication speed | 9600 baud |
Port setting | N81 |
5.3 OSDP reader settings
For OSDP readers there are some specific settings.
It’s possible to setup the buzzer time when a card is recognized, this can be done at the door behavior tab of the reader.
Buzzer time | card recognized | |
|---|---|
Setting | Behavior |
Empty | No buzzer when card is recognized |
1 - 15 | buzzer time (1/10 sec) |
| Info |
|---|
Most used setting for buzzer time = 2 |
...
| Note |
|---|
Once a key is set into the reader it cannot be cleared or rewritten by the system if the current key is not known. (not allowed in the OSDP protocol, security risk). If the key must be cleared (Reset) follow the procedure what is delivered by the reader manufacturer. |
...
Enter the following data:
Name: | OSDP NVITE DESfire |
Card number presentation: | Select the existing DESFire presentation |
Format: |
|
Reader communication protocol: | ABA |
Card type: | None |
Data Length: | 16 |
System code: |
|
Start: | 5 |
Code: | 002974 (for demo cards) |
Facility: |
|
Start: | 1 |
Code: | 0600 |
Card number: |
|
Start | 11 |
Length: | 6 |
Modulo: |
|
Offset: |
|
Interpretation selection |
|
Start: | 1 |
Length: | 0 |
Code: |
|
Expire date: |
|
Start | 1 |
Length: | 0 |
Date control: | No expire date check |
Format: | YYMMDD |
Keypad | Do not change |
Offline Validity: | Do not change |
SV WO: | Do not change |
Consistency: | Do not change |
7.2 NVITE Crypted QR
The card data interpretation below can be linked to a standard QR code presentation, which can be generated using the card number presentation wizard.
...
After refreshing the page, you will see a new card number presentation and a corresponding card data interpretation. Modify the card data interpretation settings as follows:
Name: | OSDP NVITE QR crypted |
Format: |
|
Reader communication protocol: | Hexadecimal |
Card type: | QR barcode |
Encryption: | Aes128 |
Encryption key: | your key |
Data Length: | 32 |
System code: |
|
Start: | 1 |
Length: | 6 |
Code: | 000b9e (for demo cards) |
Facility: |
|
Start: | 1 |
Length: | 11 |
Code: | 00000000000 |
Card number: |
|
Start | 7 |
Length: | 6 |
Modulo: |
|
Offset: |
|
Interpretation selection |
|
Start: | 0 |
Length: | 0 |
Code: |
|
Expire date: |
|
Start | 13 |
Length: | 8 |
Date control: | Expire date check, including date |
Format: | YYYYMMDD |
Keypad | Do not change |
Offline Validity: | Do not change |
SV WO: | Do not change |
Conssistancy: | Do not change |
Filter: |
|
Start tag: | 0300 |
End tag: |
|